עדכון גירסה למקרן W1070 benq 1.08 + כיול מקצועי ומדריך

[roei3gs]

למי שמעוניין לעדכן ויש לו גירסה ישנה בבקשה הנה לינק להורדה לגירסה נבדק ועובד ללא בעיה הנה מדריך קרדיט לאתרים http://www.hifivision.com/
http://www.avsforum.com/

1. Write down all your settings before starting an update. (If you do not you will loose all your settings)
2. I suggest that you create a new folder on your desktop called 1070 firmware in the new folder.
3. Download the download tool and unzip it to the new folder.
4. Download the new separate 106 img file to the same folder from the link above.
5. .Install the download tool. It is called DLP composer. Also download the Flash Device Parameters file.
5A Copy the Flash Device Parameters. txt file to the DLP composer program file (It is under programs x86 DLP Composer on your C drive.) Use Copy and paste. The folder you want to paste this file to will be on the c drive after you install DLP composer.
6. Open the DLP Composer tool and go to edit, preferences.
7. When the window opens go to communication and set it to USB
8. Close this window and click on flash loader on the opening screen. A window will open.
8. Change the mark to Complete Image Download Put check in Skip Boot loader area Change 32Kb
9. On the top of the flash loader hit the browse button and go to your folder 106 img file.
10. Insert the USB cable in the min plug on the projector and into your computer. (Wait for the drivers to load. This should take a minute with windows 7 or 8
11. Unplug the projector and push the power and auto buttons at the same time. Plug in the projector while holding the buttons. The LED on the projector will turn red if you are in download mode (It must turn red to install the firmware. If it turns orange do this again until you only get the red led) This is very important.
12 Hit the Reset Bus and Start Download. The upgrade process should take about 5 minutes. A timer will start telling you how long it will take.
13. Do not unplug anything during the process. When everything completes the LED on the projector will turn to standby orange.
14. Unplug the USB cable and turn the projector on
15 You will have to put all your settings back in and turn source select to auto
16. Instructions are also available in the service manual PDF you downloaded to your folder.
17. Only do this upgrade at your own risk and if you are familiar with doing firmware updates..
18. You do not need the service tool to do the firmware update the firmware and write down your settings.

Please pay attention to Highlighted RED text above, which is imp and if missed can brick your PJ

לינק להורדת הגירסה 1.08
https://www.dropbox.com/sh/x5omnxp1vr6w ... 8_3DF7.img

זה לינק להורדת כל העדכונים גם גרסאות ישנות מדריכים פלוס התוכנות שצריך לשדרוג
https://www.dropbox.com/sh/x5omnxp1vr6wyi4/15YsjCtmTd

הנה הסבר על כל השינוים מגריסה לגירסה
W1070 Version 1.06 and W1080ST Version 1.03 are a must have.

- as it has good amount of fixes + 3D support for many more resolutions + HDMI handshake issues fixed, as everyone has faced this issue worldwide, including myself.

The fixes are thus for the w1070 firmwares:

Firmware 1.03

Problem-1- To improve the flickering when smart ECO mode + dynamic setting
Problem-2- To add “Background” color in OSD

Firmware 1.04

Problem-1- When at low temperature environment, fan oil would become thickened, cause rotational speed of
fan can’t reach target then shut down.
Problem-2- Keystone bug: When playing 3D (Frame packing), and then switch to 2D, and keystone value
can’t be kept.

Firmware 1.05

Problem-1- ISF setting cannot be saved
Problem-2- compatibility problem for some unique 3D DVD players(Philips)
Problem-3- OSD Swedish language of ”on& off” wrong translation


Firmware 1.06

Fixes:
-1- Hg bridge problem symptom: can’t turn on a projector, but NDF after transportation; few cases found in BQC.
There is Hg (Mercury) in a lamp bulb. Whenever the liquid mercury make the Short-circuit of electrodes of the lamp, the unit can’t
be turn on. To change the cooling status and lamp ignition behavior can make mercury condense at different locations of a bulb.
Due to Hg (Mercury) changing the location in lamp bulbs during transportation, it will be NDF in ASP.
-2- To improve power-on while system initializing
-3- To improve Philips DVD compatibility issue(BQC)
-4- Add 3D format as appendix
-5- Adjust Audio Curve for BQjp
-6- Japanese OSD correction for Cool and Warm (BQjp)
-7-To enhance HDMI searching speed
-8- To update RC code for new remote RCV011
-9- To modify the gain value to improve HDMI signal searching ability
-10- To add model name W1250 in Factory OSD (only W1070)

Added support for 3D formats:
1280x720p@59/94/60 Hz -- SBS added
1280x720p@50Hz - SBS added
[email protected]/24Hz - SBS added
[email protected]/60Hz - Top Bottom - added
1920x1080p@50Hz - Top Bottom - added

Firmware 1.07

ISF Night setting can’t be keep after 2D->3D timing changed
To keep lamp hour after “reset all setting in USE OSD”
To improve the 32 gray level via PS3 HDMI
Modify picture mode of “power off” icon
Modify HSG setting in No signal condition

So as you can see above, 1.06 is must have and 1.07 is not mandatory for most users, but heard 1.07 has also improved the HDMI sync times for some users, but we should acknowledge that, as most guys from Tech background will agree with me, that companies wont expose all bug fixes to customers i expect there will be lot of fixes hidden

Note: W1080ST is technically similar projector but Short Throw Lense, but has firmware numbering and firmware different.

W1080ST Version 1.03 = W1070 Version 1.06
W1080ST Version 1.04 = W1070 Version 1.07
W1080ST Version 1.05 = W1070 Version 1.08

W1080ST is behind in version, due to it being released later than W1070 which is older.

The firmware files are different for these 2 models.

Firmware 1.08
- Noise improvement / 1080p greenish problem via HDMI/VGA signal.
- Add 3D support timing: 1080p 60Hz SBS

אני הבנתי שאנשים שידרגו מגירסאות ישנות ישר ל 1.08 ללא כל בעיה אני אישית ממליץ בחום תמיכה טובה יותר בפורמטים של התלת מימד תגובה מהירה יותר של המקרן

הנה עוד בנוס קטן כיול מקצועי למקרן לתלת מימד ולשידורים רגילים השינוי משמעותי
קרדיט לפורום http://www.avforums.com/

/threads/benq-w1070-reviewer’s-recommended-best-settings.1761516/

מקווה שעזרתי בהצלחה

[בועזון]

לאחר שנודע לי על הגרסא החדשה בשרשור אחר, השתמשתי בקבצים ובהוראות בקישור הבא:
http://stevenbreuls.com/2014/04/benq-w1 ... e-upgrade/

עבד חלק וטוב.
העניין עם ה-3D היה קצת מתסכל (לא שבאמת משתמשים בזה כל כך הרבה...