שלום,
פתאום בלי אזהרה, באמצע שיטוט בין סרטים, ה XT כבה.
כשנדלק שוב הופיע מסך של בחירת שפת תפריט XT והגדרות רשת למרות שהכל הוגדר.
הוצאתי מהחשמל ומאז הוא ממאן לעבוד: בכל פעם שאני מדליק אותו הוא נדלק, מכבה את עצמו ושוב מנסה להידלק בלופ.
למישהו יש רעיון ?
מדובר על גרסא 2.4 של firmware.
Xtreamer הפסיק לעבוד פתאום (נכנס ל loop)
בכל עמוד קשוחה באתר הרישמי יש חלק בשם:
Emergency firmware download and installation instructions עם הנחיות כיצד להתקין:
Emergency firmware download and installation instructions עם הנחיות כיצד להתקין:
קוד: בחירת הכל
2.4RC3 Emergency (md5sum: bf466144a2c1792e6b93294216176829)
Before starting the procedure of emergency recovery - Please make sure you are using the AV RCA cables and not HDMI. Some TV HDCP protocols may cause problem to show the procedure on TV.
(1) Download the Xtreamer Emergency file
(2) Extract the file install.img
(3) Format a USB stick FAT32 and copy the “install.img” file to the root.
(4) Disconnect all the cables, remove WIFI antenna and any other USB storage devices. Take the unit out of the electricty power on the wall for 30 minutes. Plug the power in again.
(5) In Remote control, press “Home”(release button) -> “3”(release button) -> “Power”(release button). Press the buttons with a 1 sec pause.
Any other sequence will fail and nothing will happen as the call for this procedure is initiated by HOME button pressed first...
If the firmware is not in the root of the USB the process will fail as the process seek the .img in the USB root.
Process Emergency upgrade should be visible on the screen if done correct.
Please note : After “intro” screen, if system boots without further update procedure, re-try emergency firmware update while powering-off the unit. It means you did not do it in the correct way. PRESS the HOME first and after 3 and after POWER while the unit is OFF.
It might be necessary to run the procedure several times. If you are not successful you may need to use another USB stick.
הערה קטנה: זה לא עבד לי עם HDD חיצוני, רק עם DOK וגם זה אחרי פירמוט, והורדה של U3 (מ SanDisk)yakirdvir כתב:בכל עמוד קשוחה באתר הרישמי יש חלק בשם:
Emergency firmware download and installation instructions עם הנחיות כיצד להתקין:קוד: בחירת הכל
2.4RC3 Emergency (md5sum: bf466144a2c1792e6b93294216176829) Before starting the procedure of emergency recovery - Please make sure you are using the AV RCA cables and not HDMI. Some TV HDCP protocols may cause problem to show the procedure on TV. (1) Download the Xtreamer Emergency file (2) Extract the file install.img (3) Format a USB stick FAT32 and copy the “install.img” file to the root. (4) Disconnect all the cables, remove WIFI antenna and any other USB storage devices. Take the unit out of the electricty power on the wall for 30 minutes. Plug the power in again. (5) In Remote control, press “Home”(release button) -> “3”(release button) -> “Power”(release button). Press the buttons with a 1 sec pause. Any other sequence will fail and nothing will happen as the call for this procedure is initiated by HOME button pressed first... If the firmware is not in the root of the USB the process will fail as the process seek the .img in the USB root. Process Emergency upgrade should be visible on the screen if done correct. Please note : After “intro” screen, if system boots without further update procedure, re-try emergency firmware update while powering-off the unit. It means you did not do it in the correct way. PRESS the HOME first and after 3 and after POWER while the unit is OFF. It might be necessary to run the procedure several times. If you are not successful you may need to use another USB stick....
