ברשותי אונקיו 606. אליו אני מחבר מחשב נייד באמצעות HDMI
בזמן האחרון כשאני מחבר את המחשב הרסיבר כבה אחרי כמה שניות של צפיה
למישהו יש מושג מה זה יכול להיות?
תודה
הצילו!!! הרסיבר כבה!!!
-
netavi
-
- חבר שרק התחיל

- תגובות: 46
- הצטרף: ינואר 2008
נערך לאחרונה על ידי netavi ב 21/09/2009 17:28, נערך פעם 1 בסך הכל.
- Nba
-
- חבר במועדון 10K

- תגובות: 10131
- הצטרף: ספטמבר 2005
בלי שום הודעה על הצג?
הוא מספיק מאוורר?
(כדאי שתשנה את הכותרת על מנת למקד את השאלה).
הוא מספיק מאוורר?
(כדאי שתשנה את הכותרת על מנת למקד את השאלה).
-
netavi
-
- חבר שרק התחיל

- תגובות: 46
- הצטרף: ינואר 2008
הרסיבר מאוורר ואין שום הודעה
אני רואה תמונה של המחשב על הטלויזיה ואחרי כמה שניות הרסיבר "קופץ" (כבה) והנורית האדומה שעליו מהבהבת
- Nba
-
- חבר במועדון 10K

- תגובות: 10131
- הצטרף: ספטמבר 2005
תעבור על כל החיבורים של הרמקולים ותבדוק שאין קצר, שאחד לא נוגע בשני.
- gal2424
-
- חבר פעיל

- תגובות: 61
- הצטרף: אוגוסט 2009
גם לי קרה את זה עם ה602 של אונקיו סיכוי גבוה שקצר..
מגבר אחר כבר היה הולך....
מגבר אחר כבר היה הולך....
- DannyZ
-
- חבר ותיק

- תגובות: 1624
- הצטרף: מרץ 2006
- מיקום: תל אביב
[left]The AV receiver turns off as soon as it’s turned on
• The amp protection circuit has been activated.
Remove the power cord from the wall outlet immediately.
Disconnect all speaker cables and input sources,
and leave the AV receiver with its power cord disconnected
for 1 hour. After that, reconnect the power cord
and set the volume to maximum. If the AV receiver
stays on, set the volume to minimum, disconnect the
power cord, and reconnect your speakers and input
sources. If the AV receiver turns off when you set the
volume to maximum, disconnect the power cord, and
contact your Onkyo dealer.[/left]
• The amp protection circuit has been activated.
Remove the power cord from the wall outlet immediately.
Disconnect all speaker cables and input sources,
and leave the AV receiver with its power cord disconnected
for 1 hour. After that, reconnect the power cord
and set the volume to maximum. If the AV receiver
stays on, set the volume to minimum, disconnect the
power cord, and reconnect your speakers and input
sources. If the AV receiver turns off when you set the
volume to maximum, disconnect the power cord, and
contact your Onkyo dealer.[/left]